*New: LC Control: new control module for Hitachi - L-6200 pump - available for testing
*New: LC Control: Shimadzu LC-10/20 system control - support for SPD-M20A - available for testing
*New: LC Control: Shimadzu LC-10/20 system control - support for SIL-10Axl - available for testing
*New: LC Control: Control for Rheodyne Valve MX II series (USB) - available for testing
*New: Control: New Auxiliary Digital Input Module (DIM) enables to use the DIgital Input Device (p/n DID01) connected to a COM port to provide two digital inputs in Clarity.
*New: LC Control: Shimadzu LC-10/20 system control - option to check detector cell and AS cooler temperatures as condition for system ready. New checkbox, the temperatures are checked after sending method to be within +/- 1.5 C for the system to be Ready.
*New: LC Control: Valve - modified options in the Method Setup Event table suitable for fraction collectors. The Output field offers a list box with options Position and Next. For the Position, a position within the available range should be entered. For the Next, the next available position will be used.
*New: Extensions - GPC: Import chromatogram -the imported chromatograms will have the Alpha nad K parameters set according to the setting in the Single Analysis dialog.
*New: AS Control: Spark Triathlon, Endurance - new option to assign the digital Start IN input to the autosampler in the System Configuration dialog - Acquisition Card field.
*New: LC Control: LabAlliance 605 Column Oven - LC UNI thermostat script - available for testing
*New: AS Control: AS Spark Triathlon - Method Setup dialog - User or Mix method - new option for setting destination vial relative to sample vial
*New: LC Control: Ecom pump - actualized UNI LC Pump driver profiles
*New: LC Control: Analytical Technologies - UNI LC pump driver profiles for ALC 2010, 2100 and ColumWash pumps
*New: LC Control: HTA HT300L and LV samplers - the synchronisation by the external ready signal was disabled for those models (the synchronisation wire is not necessary anymore)
#Fixed Bug: AS Control: HTA As300 and HT200 - Method parameters validation: if you are using sampler's ISTD then upgrade firmware 3.21 or newer otherwise Clarity will check method differently from the sampler.
#Fixed Bug: Control: Decade II detector - the default configuration (digital inputs) was changed
#Fixed Bug: AS Control: Spark Triathlon - minor amendment in the Method Setup - AS dialog - Wash Options
#Fixed Bug: AS Control: Spark Triathlon - problems during sequence mode
#Fixed Bug: AS Control: Spark Marathon - check for valid injection volume for partial loop method (from version 2.6.3.313)
#Fixed Bug: Export of user columns in Result table
#Fixed Bug: AS Control: in prep ahead/sequence mode - wrong vials could be used after sequence interuption
#Fixed Bug: LC Control: Agilent 1100 detectors - problem in redrawing the Method Setup - LC dialog during downloading time table from detector
#Fixed Bug: Hardvare: INT9 - fixed bug in a system driver (since version 5.0.3.2) - closing a Clarity instrument caused data acquisition interruption on other running instruments
#Fixed Bug: Control: Knauer drivers updated to version 2.6.0.1069
*New: LC Control: Shimadzu LC-10/20 system control - support for SPD-M20A - available for testing
*New: LC Control: Shimadzu LC-10/20 system control - support for SIL-10Axl - available for testing
*New: LC Control: Control for Rheodyne Valve MX II series (USB) - available for testing
*New: Control: New Auxiliary Digital Input Module (DIM) enables to use the DIgital Input Device (p/n DID01) connected to a COM port to provide two digital inputs in Clarity.
*New: LC Control: Shimadzu LC-10/20 system control - option to check detector cell and AS cooler temperatures as condition for system ready. New checkbox, the temperatures are checked after sending method to be within +/- 1.5 C for the system to be Ready.
*New: LC Control: Valve - modified options in the Method Setup Event table suitable for fraction collectors. The Output field offers a list box with options Position and Next. For the Position, a position within the available range should be entered. For the Next, the next available position will be used.
*New: Extensions - GPC: Import chromatogram -the imported chromatograms will have the Alpha nad K parameters set according to the setting in the Single Analysis dialog.
*New: AS Control: Spark Triathlon, Endurance - new option to assign the digital Start IN input to the autosampler in the System Configuration dialog - Acquisition Card field.
*New: LC Control: LabAlliance 605 Column Oven - LC UNI thermostat script - available for testing
*New: AS Control: AS Spark Triathlon - Method Setup dialog - User or Mix method - new option for setting destination vial relative to sample vial
*New: LC Control: Ecom pump - actualized UNI LC Pump driver profiles
*New: LC Control: Analytical Technologies - UNI LC pump driver profiles for ALC 2010, 2100 and ColumWash pumps
*New: LC Control: HTA HT300L and LV samplers - the synchronisation by the external ready signal was disabled for those models (the synchronisation wire is not necessary anymore)
#Fixed Bug: AS Control: HTA As300 and HT200 - Method parameters validation: if you are using sampler's ISTD then upgrade firmware 3.21 or newer otherwise Clarity will check method differently from the sampler.
#Fixed Bug: Control: Decade II detector - the default configuration (digital inputs) was changed
#Fixed Bug: AS Control: Spark Triathlon - minor amendment in the Method Setup - AS dialog - Wash Options
#Fixed Bug: AS Control: Spark Triathlon - problems during sequence mode
#Fixed Bug: AS Control: Spark Marathon - check for valid injection volume for partial loop method (from version 2.6.3.313)
#Fixed Bug: Export of user columns in Result table
#Fixed Bug: AS Control: in prep ahead/sequence mode - wrong vials could be used after sequence interuption
#Fixed Bug: LC Control: Agilent 1100 detectors - problem in redrawing the Method Setup - LC dialog during downloading time table from detector
#Fixed Bug: Hardvare: INT9 - fixed bug in a system driver (since version 5.0.3.2) - closing a Clarity instrument caused data acquisition interruption on other running instruments
#Fixed Bug: Control: Knauer drivers updated to version 2.6.0.1069
Product Line
Product Version
2.6